Tyan-computer Transport GT20 B3970-U Bedienungsanleitung

Transport GT20B3970-UService Engineer’s Manual

2 Chapter 1: Overview1.3 FeaturesEnclosure• Industry 19” rack-mountable 1U chassis– (4) 3.5” HDD bays– (1) slim CD-ROM bay • Dimension: D 22.4 x W 17.

Chapter 1: Overview 31.4 UnpackingIf any items are missing or appear damaged, contact your retailer or browse to TYAN’s Web site for service: http://w

4 Chapter 1: OverviewMainboard ManualBarebone ManualRail KitMounting Bracket x 4Sliding BracketsFront L-Bracket x 2Rear L-Bracket x 2Screws KitSliding

Chapter 1: Overview 51.5 About the ProductThe following views show you the product.1.5.1 Front View1.5.2 Rear ViewCD-ROM DriveHard Drive Bay x 4HDD ac

6 Chapter 1: Overview1.5.3 LED DefinitionFront PanelRear I/O LED LED Color State DescriptionPower GreenOFFONOFFPowe

Chapter 1: Overview 71.5.4 Internal View1 261191057831241. PCI-X Slot2. Memory Slots3. Power Connector4. EPS Power Supply5. System Fans6. M1012 Adapte

8 Chapter 1: Overview1.5.5 Motherboard (S3970) Block Diagram

Chapter 1: Overview 91.5.6 Motherboard Layout

10 Chapter 1: Overview Jumpers & ConnectorsJumper/ConnectorFunctionJ2/J3 3-pin Back Panel Fan ConnectorJ4/J2

Chapter 2: Setting Up 11Chapter 2: Setting Up2.0.1 Before You BeginThis chapter explains how to install the CPU, CPU heatsink, memory modules, and har

12 Chapter 2: Setting Up2.0.4 PrecautionsComponents and electronic circuit boards can be damaged by discharges of static electricity. Working on a sys

Chapter 2: Setting Up 132.1 Rack MountingAfter installing the necessary components, the Transport GT20 can be mounted in a rack using the supplied rac

14 Chapter 2: Setting UpInstalling the Inner Rails to Chassis1. Screw the mounting ear to each side of GT20 as shown using 2 screws from the supplied

Chapter 2: Setting Up 154. Locate the front and rear brackets.5. Reserve 40mm on the front bracket. Secure the front bracket to outer rail with 2 M4-4

16 Chapter 2: Setting Up6. Reserve the distance same as in Step 2 on rear bracket. Secure the rear bracket to outer rail with 2 M4-4L(C) screws.7. Sec

Chapter 2: Setting Up 17Rackmounting the Server8. Draw out the middle rail to the latch position.9. Lift the chassis and then insert the inner slide r

18 Chapter 2: Setting Up11. Secure the mounting ears of chassis to the rack with 2 M4-15L(F) screws.NOTE: To avoid injury, it is strongly recommended

Chapter 2: Setting Up 192.2 Installing Motherboard ComponentsThis section describes how to install components on to the motherboard, including CPU, me

20 Chapter 2: Setting Up2.2.2 Installing the MemoryFollow these instructions to install the memory modules on the motherboard.1. Locate the memory slo

Chapter 2: Setting Up 212.2.3 Installing the CPU and Heatsink Follow these instructions to install the CPU and CPU heat-sink.1. Locate the CPU socket.

PREFACECopyrightThis publication, including all photographs, illustrations, and soft-ware, is protected under international copyright laws, with all r

22 Chapter 2: Setting Up4. Open the socket in the direction as illustrated.5. Place the CPU on the CPU socket, ensuring that pin 1 is located in the r

Chapter 2: Setting Up 237. Press the CPU socket lever down in the direction shown to secure the CPU.8. Secure the heatsink to the motherboard using tw

24 Chapter 2: Setting Up2.2.4 Installing the PCI-X CardFollow these instructions to install a PCI-X card.1. Push the tab of PCI-X slot on the rear pan

Chapter 2: Setting Up 254. Push the tab of PCI-X slot on the rear panel in the direc-tion as shown to secure PCI-X card.

26 Chapter 2: Setting Up2.3 Installing the External Hard DriveThe GT20 chassis kit supports external SATA or SAS hard drives.Follow these instructions

Chapter 2: Setting Up 274. Using 4 HDD screws to secure the HDD.5. Reinsert the drive tray into the chassis (A), ensuring that the drive tray is compl

28 Chapter 2: Setting Up2.4 Installing the Slim FDD (Option)1. Locate the two FDD rails and screws from the FDD kit. Secure the two rails to FDD using

Chapter 2: Setting Up 295. Connect the FFC cable to the connector on M1012 adapter board.6. Locate the FDD cable from FDD kit. Connect the wrinkle sid

30 Chapter 2: Setting UpNOTE

Chapter 3: Replacing Pre-Installed Components 31Chapter 3: Replacing Pre-InstalledComponents3.1 IntroductionThis chapter explains how to replace pre i

ii Federal Communications Commission (FCC)Notice for the USA Compliance Information State-ment (Declaration of Conformity Procedure) DoC FCC Part 15:

32 Chapter 3: Replacing Pre-Installed Components3.1.3 PrecautionsComponents and electronic circuit boards can be damaged by static electricity. Workin

Chapter 3: Replacing Pre-Installed Components 333.2 Disassembly FlowchartThe following flowchart outlines the disassembly procedure.Rear ComponentsCha

34 Chapter 3: Replacing Pre-Installed Components3.3 Removing the CoverBefore replacing any parts you must remove the chassis cover.Follow these instru

Chapter 3: Replacing Pre-Installed Components 353.4 Replacing Motherboard ComponentsFollow these instructions to replace motherboard compo-nents, incl

36 Chapter 3: Replacing Pre-Installed Components3. Disconnect all cables from front panel, USB, fans and SATA connectors.3.4.2 Removing the Motherboar

Chapter 3: Replacing Pre-Installed Components 373.5 Replacing the Slim CD-ROMFollow these instructions to replace the CD-ROM.1. Remove power and data

38 Chapter 3: Replacing Pre-Installed Components3. The CD-ROM drive will be freed from the drive bay after pressing the tab.4. Remove two screws that

Chapter 3: Replacing Pre-Installed Components 393.6 Replacing the LED Control BoardFollow these instructions to replace the LED control board.1. Remov

40 Chapter 3: Replacing Pre-Installed Components4. Lift the LED control board free from the chassis. After replacement, insert the unit into the chass

Chapter 3: Replacing Pre-Installed Components 413.7 Replacing the M1012 Adapter Board1. Remove all of those cables connected to the adapter board, inc

iiiAbout this ManualThis manual provides you with instructions on installing your Transport GT20. This manual is intended for experienced users and i

42 Chapter 3: Replacing Pre-Installed Components2. Remove six screws to release the adapter board. Refer to p.46 for the location.Fan Cables

Chapter 3: Replacing Pre-Installed Components 433.7.1 M1012 Adapter Board Features for B3970-UJ16: LCM Connector J7:Fan Tach & PWM Connector J5: F

44 Chapter 3: Replacing Pre-Installed Components3.7.2 M1012 Adapter Board Connector Pin Definition J1 TYFP Front Panel Connector

Chapter 3: Replacing Pre-Installed Components 45 J3 LAN/ID LED ConnectorFAN Signal Related Connector Pin DefinitionNOTE: The FAN signal naming is b

46 Chapter 3: Replacing Pre-Installed Components J13 Fan TACH Connector J14 Fan TACH Connector

Chapter 3: Replacing Pre-Installed Components 47 J10 Fan Connector J11 Fan Connector

48 Chapter 3: Replacing Pre-Installed Components J5 Fan Connector J15 & J16 LCM Connectors JP1 Fan In

Chapter 3: Replacing Pre-Installed Components 493.8 Replacing the SATA Backplane1. After removing the M1012 adapter board, disconnect those cables con

50 Chapter 3: Replacing Pre-Installed Components4. Release the adapter board free from the bracket.5. After replacement, place and secure the unit int

Chapter 3: Replacing Pre-Installed Components 513.8.1 SAS/SATA Backplane (M1208) FeaturesU4, SAS/SATA4 ConnectorU3, SAS/SATA3 ConnectorU2, SAS/SATA2 C

iv SAFETY INFORMATIONBefore installing and using the Transport GT20, take note of the fol-lowing precautions:– Read all instructions carefully.– Do n

52 Chapter 3: Replacing Pre-Installed ComponentsPW1 Power ConnectorJ4, SAS/SATA 4 J3, SAS/SATA 3J2, SAS/SATA 2 J1, SAS/SATA 1PW2 Power ConnectorConnec

Chapter 3: Replacing Pre-Installed Components 533.9 Replacing the Power Supply1. Remove two screws securing the power supply to the chassis.2. Remove

54 Chapter 3: Replacing Pre-Installed ComponentsNOTE

55Appendix I: BIOS DifferencesThe BIOS of B3970-U is similar to the BIOS of S3970G2N-U. There is only one menu different. You may refer to the attach

56 S3970 Advanced/Hardware Health ConfigurationTable of DifferencesBIOS Setup Utility AdvancedHardware Health Configuration Enables Hardw

57Appendix II: Cable Connection TablesSATA CableFAN CableTable 1: B3970-UG20S4H ModelM1204 SATA Backplane Connect to MotherboardSATA 1 Æ SATA 1SATA 2

58 Power Supply CableTable 4: Power Supply to MotherboardPower Supply Connect to MotherboardP1 24-pin power cable Æ PW1 24-pin connectorP2 8-pin powe

59Other CablesTable 7: M1012 Adapter Board to MotherboardM1012 Connect to MotherboardJ1 Front Panel connector Æ J24 (TYFP1)J3 (LAN / ID LED) Æ J5 (TY

60 Appendix III: Installing SMDC CardsThe following provides you with the information on installing SMDC cards. You may refer to the following for in

61Installing M3289 into HDD Tray1. Fold up the cable.2. a: Choose a HDD tray. b: Insert the cable into the rear of HDD tray. c: Pull the cable out.3.

vTable of ContentsChapter 1:Overview1.1 About the Transport GT20 B3970-U . . . . . . . . . . . . . . . . . . . . . . . 11.2 Product Model. . . . . .

62 4. Align M3289 in reverse with 4 “M1” stand-offs. Secure the SMDC with 4 screws as illustrated.5. Secure M3289 onto HDD tray as illustrated.6. Ins

63Installing M3290/M3291 into HDD tray1. Secure a removable stand-off of 13.5mm to the location of “M2” stand-off as illustrated on SMDC bracket.2. S

64 4. a: Inset the cable into the rear of HDD tray. b: Connect the cable to M3290. c: Insert and secure HDD tray.5. Arrange and connect the cable to

65Installing M3290/M3291 into GT24 ChassisNOTE: The products produced now may not support the pro-cedures below. We’ll provide you with the upgraded

66 4. Connect the cable to M3290. Arrange and connect the cable to SMDC connector on mainboard. Be careful not to block the air flow.5. Reconnect the

67NOTE

68 Technical SupportIf a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been c

693. Contact your dealer for help BEFORE calling TYAN.4. Check the TYAN user group: alt.comp.periphs.main-board.TYANReturning Merchandise for Service

vi 3.7 Replacing the M1012 Adapter Board . . . . . . . . . . . . . . . . . . . . . . 413.7.1 M1012 Adapter Board Features for B3970-U . . . . . . . .

Chapter 1: Overview 1Chapter 1: Overview1.1 About the Transport GT20 B3970-UCongratulations on your purchase of the TYAN TransportTMGT20 (B3970-U), a